Do It Yourself Bath Setup.
Do It Yourself Bath Setup.
Blog Article
Are you in search of insight on Tools You Need to Install a New Bathtub ?
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard task. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall surface to remove the old tub and position the new tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This write-up will certainly aid you set up a brand-new tub in your restroom if you have already bought a new bathtub and also do not require to alter the arrangement of your previous water supply pipes.
Your devices and also product checklist ought to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome as a result of the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in position with the supplier provided backnut. As soon as the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former type should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Tub
Making use of the two wooden boards under its feet, put the bath tub in the required setting. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the tub till the level reads level.
To set up faucets, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Switch on the supply of water as well as inspect all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and also inspect the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.
Getting ready for the Setup
First of all, the sustaining frame provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to see to it that if the faucet features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall surface between the bathroom and the tiling, leading to issues with dampness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are marketed in tubes and also cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can fracture relatively very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on Installing A Bathtub, I imagined sharing that piece of content was worthwhile. You should set aside a second to promote this entry if you appreciated it. Many thanks for going through it.
Call Today Report this page